Get 20% more hydrogen than nameplate in your next turnaround

A foil-supported catalyst meets increased hydrogen demand within a 
normal turnaround.

Johnson Matthey Catalysts Technologies

Viewed : 909

Article Summary

The International Maritime Organization’s (IMO) low sulphur marine fuel regulation is in place for 2020. There are still technology decisions being made and some wait and see approaches as to how the regulation will be managed. It is understood that a predominant portion of the low sulphur fuel required for meeting this regulation will be from increased low sulphur diesel production. Some complex refineries have the capacity to meet these increased hydroprocessing needs as sweeter tight oils have replaced sour crudes. This increased diesel production will require more hydrogen production from the site. Processing the tight oils has increased production of catalytic reformers, resulting in more hydrogen contribution to the site than in previous years. With this additional source of hydrogen on site, many hydrogen plants are running at 70-80% utilisation. The low sulphur marine fuel regulation, as well as refiners hydroprocessing more bio based feeds that are lean on hydrogen, is creating a step change in hydrogen demand. Even with the increase in hydrogen availability from the catalytic reformer, many refiners are needing about 20% more hydrogen than nameplate within their refineries.

Traditionally, the on-site choices that a refiner has for a 20% uprate are either building a grassroots hydrogen plant or uprating an existing hydrogen plant by adding a heat exchange reformer. These solutions tend to pose challenges for the refiner in the following ways:
- Availability of capital
- Plot plan
- Turnaround scheduling
- Compression
- Steam production
- Increased asset wear

Johnson Matthey’s Stackable Structured Reactor — Catacel SSR steam reforming catalyst technology addresses and helps minimise or remove these challenges while enabling a 20% uprate above nameplate hydrogen production. This article will address each of these challenges with respect to a 20% uprate using SSR technology.

Availability of capital
Downstream margins are under tremendous pressure and compression, reducing the availability of capital. Improvements in capital utilisation and efficiency need to be apparent for expansion projects to come into consideration. A Catacel SSR technology uprate offers one of the lowest capital usages for increased hydrogen production, thereby increasing overall return on investment. The uprate does require debottlenecking of the fired reformer to enable the process flow and increased heat load to be achieved with the fired reformer. Typically, the fired section of the steam methane reformer needs to be modified for this increased heat load, particularly the burners and ID fan. Depending on the plant, additional upgrades may be needed in the feed purification system, the outlet header of the fired reformer, and the pressure swing absorption system that purifies the hydrogen product. The level of capital needed will vary depending on the modifications required, but even with this a 20% uprate with SSR still offers lower capital for increased production by 20-50%.

Plot plan/turnaround scheduling
As an operating company considers increased capacity, some additional plot plan needs to be considered either for a grassroots plant or when adding additional equipment. Many refineries are in populated areas close to metropolitan cities, allowing limited space for expansion or addition. Most hydrogen plants have even less space available near the plant itself. Beyond having the space, extensive pre-work needs to be accomplished to make that space ready, including environmental regulations, infrastructure, and preparing the site. These activities require site access during plant operation or additional work to be accomplished within the upgrade turnaround. For complex refiners that have the hydroprocessing capacity available for additional diesel production, extension to the typical three-week turnaround schedule quickly impacts the cost of the turnaround. The missed opportunity of production can quickly add 10-30% to the cost of the project. Obviously, a grassroots hydrogen plant will require substantial space and many approvals. Most grass roots hydrogen plants are taking 24-36 months from project approval to beneficial operation. This timing is close to a full hydroprocessing turnaround cycle to achieve production. Upgrades that add equipment to the plant are challenging to complete in a three-week turnaround. Delays in the turnaround schedule can remove millions of dollars in production from being achieved. A Catacel SSR technology uprate replaces the existing pelleted reformer catalyst in the same time that it would take to load pelleted catalyst. The typical modifications to the steam methane reformer, burners, and ID fan are accomplished within the three-week turnaround.

Catacel SSR technology is a stackable structured reactor that has been designed for reformer duty. Using catalyst coated thin metal foils, the technology packs 40% more surface area per unit volume than pellets utilising the existing reformer tubes to drive the additional reaction needed for the increased flow (see Figure 2). Fired reformer performance in a hydrogen plant relies on getting the heat into the process gas. While developments have occurred through the years on pelleted reforming catalyst, the improvements are small and still rely heavily on the randomness of pelleted catalyst loading. The patented design of Catacel SSR technology directs the process gas to encounter all the catalyst surface available and then directs this flow against the inside tube wall to maximise heat transfer and process gas reheat while moving to the next layer of surface area in the structure. This results in a 20-30% increase in heat transfer into the process gas. The technology reactor reaction and heat transfer intensification enable a tight steam methane approach to equilibrium to be maintained with the 20% uprate achievement using the existing reformer geometry.

Many hydrogen plants are limited on feed gas compression. A 20% increased flow rate can put too much resistance to flow on the feed gas compression for a pellet loaded reformer, making the uprate unachievable. In a similar way, adding a heat exchange reformer adds additional resistance to flow and added pressure drop through the added piping and heat exchange reformer equipment. The patented design and flow pattern of Catacel SSR can reduce the reformer pressure drop by 20% (see Figure 3). The steam methane reformer pressure drop can be as much as 60-70% of the flow sheet pressure drop. A 20% uprate adds no additional pressure drop to the steam methane reformer, minimising the resistance to flow on the feed gas compressor.

Steam production
Most hydrogen plants produce more steam through the heat recovery system of the hydrogen plant flowsheet than can be used in the hydrogen plant, making it a net steam exporter. The steam is used within the overall steam system of the refinery for hydroprocessing units and for driving some of the major refinery equipment. While several refiners are moving from steam driven to electrically driven equipment, many still rely on and value the steam export from the hydrogen plant for the rest of the refinery. Adding a heat exchange reformer depends on the fired steam methane reformer to produce the process steam, reducing or eliminating steam export from the hydrogen plant. With a SSR technology 20% uprate, additional export steam can be produced for the refinery. Additionally, if there are limits on the hydrogen plant process gas boiler/steam raising system, the technology is able to operate at lower steam to carbon ratios as it is more reactive, changing the conditions throughout a natural gas fired reformer to avoid carbon formation.

Add your rating:

Current Rating: 4

Your rate: